• brownstoneboys

Ikea #DIY Hack. Making Over an Existing Piece of Furniture

Updated: Mar 6



Before & After of our DIY Ikea Hemnes Hack


This #valentinesday we’re embracing our strongest love/hate relationship ever..... Ikea! 💔💔

We all have that one Ikea piece of furniture that’s been with us a little too long. For us, it’s the Hemnes 3 drawer that’s hiding in our guest bedroom. We decided it was time for a little #diy love-makeover. This makeover cost us under $50 and took us just a couple of days to make! Now, we have a new "old" dresser


TOOLS:

  • Cordless drill & drill bit

  • Stapler & staples

  • Paintbrush

  • Clamps (or tape to hold the moulding in place while the glue dries

  • Jigsaw

  • Mitre Saw (Alternatively: Fine saw & mitre block)

  • (If you don't have power tools and don't want to get any, you can take the drawer fronts to a local wood store and they might cut it for a small fee.)


SUPPLIES:

  • Ikea Hemnes Chest of Drawers (we have had ours for over 8 years!)

  • Handles –we got ours from House of Antique Hardware

  • Cane Webbing- Amazon (cheap and ships fast!). Make sure you order a little overage

  • Moulding for Cabinets- we picked up simple 1/4" rounds at Home Depot. Our advice is to get one that is on the smaller side and doesn't feel too large in the drawer.

  • Sandpaper

  • Wood filler

  • Wood Glue – this is our favorite wood glue

  • Paint – we went with Clare Paint Greyish. Clare has our favorite colors to elevate any space. We love that this color is a mix of grey, white and green!



1. DISASSEMBLE THE CHEST OF DRAWERS


You will want to get everything out of the drawers. We have been hoarding a lot of our clothes we don't usually wear in these drawers. So this gave us the perfect opportunity for some early spring cleaning. Once everything was cleared out, we removed the drawers and then took off the existing hardware. It's Ikea, so you won't need any special tools for this - a screw driver will do! Remove the cabinet fronts and make sure to keep the screws for them!


2. MEASURE, MARK & CUT

Next, cut the square holes into the drawers. You'll want to decide how much border you want around the webbing. You don’t want it to be too narrow otherwise it could leave the drawer too weak and don’t forget that you also still have to have enough space to attach your new handles, too (if you will be using handles!)


We went with about 2". Measure all the way around and draw the square you’ll be cutting out onto the drawer front. Now you're ready to grab your jigsaw and start cutting! If you don't have any power tools you can bring this to a local wood shop and they may be able to cut it for you. But we recommend having a few handy tools around and maybe this is a good project to get your toolbox started! Before you can start cutting you'll need to drill a hole inside the area you'll be removing that’s big enough for you to insert your jigsaw blade. Carefully cut out the square and try to follow the lines exactly. Don't be discouraged if this is difficult at first if it's your first time using a jigsaw you'll need a bit of practice. You will also be putting trim around the cut edge to hide some imperfections.

3. SMOOTH THE EDGES & ATTACH THE MOULDING

Sand all edges with sandpaper and make sure everything is as smooth as possible. Since the edge where you cut will be unfinished (and possibly with some imperfections from the cutting) you'll want to hide it with moulding. We used a 1/4 round trim to give it nice curved edge detail. You need a miter saw or a miter box to cut the moulding on a 45° angle and miter it at the corners. If you've never done this before our advice is to get an extra couple of lengths of moulding. It's a little tricky and you might have to re-do a few of them.



Assemble the moulding into the cutout to make sure it all fits. If it's not perfect at the miter joints and if there are small gaps where the moulding meets the cutout it's OK! We're going to fill it with some wood filler before painted. Glue the mouldings onto the cut edge and use clamps to hold it into place until it dries. If you don't have clamps just hold it in place for about 2 minutes and it should be good from there. It should be dry enough to continue after a couple of hours, but we waited until the next day.


When it’s dried, fill any gaps, uneven cuts, or chips from the cutting with some wood filler and let it dry before sanding everything so that it’s smooth and ready to prime and paint. The wood filler is sand-able and paintable so you won't see these imperfections after it's painted.

4. SAND, PRIME & PAINT EVERYTHING

When you’ve finished all cutting, glueing and filling it’s time to give everything, including the entire dresser, a sand with some 120 grit sandpaper. We just did ours by hand!


Sanding the surface will roughen it up ever so slightly and provide a good base for the paint to stick. Give everything a wipe down to make sure it's dust free before painting.



Now we could have used primer (might be recommended) but we were working with Clare Paint so that we know is a durable paint. We skipped priming since the existing cabinets were white and just decided to give a couple coats of fresh paint. Don’t forget that you also have to sand between every coat of paint to remove any imperfections, air bubbles and provide more little grooves for the next coat of paint to stick to.

5. ATTACH THE WEBBING

When you’ve finished painting and everything has thoroughly dried (give it a good 24 hours just for good measure) you can start to update your Hemnes dresser with cane webbing. Flip over the front of your drawers and staple a piece of webbing over the opening. Cut and measure the webbing first! Also, we made sure to flatten our webbing a couple days in advance. It comes rolled up and will be hard to work with if it's constantly curling up on you.




6. ASSEMBLE THE DRAWERS & ADD HANDLES

Once everything is looking like its back to being a dresser, drill the holes for your new handles. We used these beautiful handles from House of Antique Hardware which meant that we had to drill two holes into each of the larger drawers and one each in the smaller drawers.


TIP- we could have spent another couple hours measuring exact screw locations for the hardware but we just used painters tape to mark the screw holes and then transfer that from the tape onto the the drawers! This will save you so much time and be more precise!



7. PUT YOUR CLOTHES BACK IN & A NEW DRESSER!

We’re absolutely in love with how this Ikea Hemnes dresser with cane webbing turned out! It's fitting right in with our vintage botanical room and the dresser has a whole new life that we will enjoy for several more years!






We’d love to know what you think of our Ikea Hemnes dresser with cane webbing! Let us know in the comments below! Make sure to check out our Instagram for more details!




1,306 views0 comments

Recent Posts

See All
  • Instagram Social Icon
  • Pinterest Social Icon
  • Twitter Social Icon

©2020 by Brownstone Boys.